A clear filter should be invisible. If your files look softer with glass in front of the lens, the glass is the reason, and the cause is nearly always something you can check yourself.

Since March 2025 I have kept an XT996S on the front of the OM System 12-40mm f/2.8 PRO II on my Panasonic GH7. Shoot the same scene with it and without it and I cannot see a change in image quality. That is the whole sharpness claim I make here, and it covers one lens on one body. I have not run a controlled comparison on everything else I own.

Two different kinds of soft

Not every soft frame has the same cause, and the fix is not the same either.

Contrast loss looks soft but stays sharp. The blacks lift towards grey, the frame looks flat, and the detail is still in the file. That is stray light bouncing between the filter and the front element. Uncoated glass throws back roughly 8% of the light that enters the lens across its two surfaces, and that light washes over the whole frame.

Resolution loss looks soft and the detail is actually gone. Hard edges go mushy, micro-contrast disappears, and no slider brings it back. This is what happens when the two surfaces of the filter are not parallel. A small wedge acts like a weak prism, and the lens has no way of correcting for a prism it cannot see. The practical effect scales with focal length: the same filter that leaves a 24mm frame clean can mush up the corners of a 200-600mm.

You can tell the two apart at 100% on a hard edge, a roofline against the sky or lettering on a shopfront. Crisp edges over grey shadows means flare. Soft edges means the glass.

What to check before you blame the lens

Reflectance and transmission decide how much stray light comes back at you and how much of the scene survives the trip. The XT996S is rated at an average reflectance of ≤0.25% and an average transmission of ≈99.6%. The XT996 PRO is rated at ≈0.08% reflectance and the same ≈99.6% transmission. Lower reflectance means less haze over the blacks and fewer ghost spots when a light source sits just outside the frame; that transmission figure means your meter behaves as if the glass were not there.

Coating decides how many surfaces are doing the work. The XT996S carries a double-sided 28-layer multi-coating, the XT996 PRO a double-sided 36–48 layer. Both faces need it, because the rear surface is the one that throws light back down the barrel.

Thickness changes focus. A filter adds a layer of glass in front of the lens, so at close focus the extra glass can stop the front element from getting as close to the subject as the lens alone would, and on lenses that focus by moving internal groups it can nudge infinity focus. If a frame looks soft only at infinity and only with the filter on, take the filter off and look again before you blame the coating.

Dirt is the cheapest of the four and the one I forget. Fingerprint oils scatter light the way haze does. A dirty filter is the fastest way to convince yourself that filters soften photos.

The setup I keep

One filter stays on the 12-40 PRO II and it stays there.

The lens occasionally scrapes against the side of the bag when I walk around Hong Kong with the camera in a backpack, and I have forgotten the lens cap more than once on a walk. With the XT996S on the front, neither of those makes me think about the front element at all.

At dusk along the water at the Hong Kong Palace Museum, it earns its place in a different way — it keeps the salt spray off the front group.

What it does not do is keep sand out. The 12-40 PRO II is an external zoom, and on a windy beach what worries me is grit getting into the barrel and the body. A filter on the front has no say in that.

When I would skip it

If you shoot indoors, or you never take the camera near dust, salt or sand, and a hood already covers the front element, then a filter is optional. A hood adds no glass to your light path, so it costs you nothing in transmission or in focus. The argument for putting glass in front of a lens is physical protection. Without physical risk, the second piece of glass buys you a problem instead of a solution.

Read the ø mark on the front ring of your lens and order that size — if it is hard to read, look your lens up in our lens filter finder. The XT996S is the everyday one, 39mm to 82mm, $44.99 to $79.99, and the 58mm is what sits on my 12-40 PRO II. If your Leica or Fuji body needs a thread size of its own, the XT996 PRO is the version we cut for those mounts. Orders over $99 have the $8 standard shipping waived.

— Leo Liang